Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
In this article below you can discover a lot of high-quality help and advice on the subject of How to Install a Bathtub Yourself.
Setting up a bath tub isn't precisely rocket science, however it does need strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a new one is likewise a moderately hard task. If the old tub is readily accessible, the task can relocate speedily; if you have to open a wall to remove the old tub and position the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. Ensure you have actually qualified on your own for the work and fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is much better to consider employing one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly assist you install a new bath tub in your washroom if you have currently purchased a brand-new tub and also do not require to alter the arrangement of your previous supply of water pipelines.
Your tools as well as material list ought to make up the following:
Planning for the Installation
To start with, the sustaining structure supplied with the bath needs to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will come from the pipes. When the supply pipes have been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the bathtub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the tub till the level reads level.
To mount taps, fit the bottom of the outermost adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water and also examine all joints and new pipework for leakages and tighten them if required. Fill up the bath tub as well as also examine the overflow outlet and the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub needs to wait until the bathtub has been made use of at the very least when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap as well as the sink. Secure the tap in place with the supplier supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet ports. The previous type needs to be connected to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, creating the water to pass through the wall in between the bathroom and also the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to permit the activity experienced when the tub remains in use. The sealant can fracture relatively early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily offered on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking the time to read our posting. Sharing is caring. You won't know, you might be doing someone a favor. Kudos for your time. Visit again soon.
Booking Report this page